Hello There, Guest! Register

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
New here
03-22-2012, 05:04 AM,
#28
RE: New here
As Hersute pointed-out, that kind of work can involve changes in hairstyles... you can confide in those stylists with confidence...after all, a lot of that kind of image if not actually `photo-shopped` at the end, certainly is very `cosmetic`in nature.....you see these images of people and literally it`s a case of `not a hair out of place`.
I have noticed all right that despite people saying the camera never lies, when it comes to systems, even guys who post pics here have remarked many times that `` it looks better in reality`---don`t know what it is, but digital cameras seem to really `distort` system- hair images. I think , as you wear long-ish hair, it will be far less noticeable, especially if you have a few to hand ...you can replace it easily if it begins to look `tired` early ----if I was considering going into that game, I`d really have 3 or 4 systems at the ready---no way would I `nurse` one along and hope to get away with it in a studio-setting under intense light etc...you`d need to have `good`hair on your head at every session.
Most guys who use all -tape bonds, if they need to do a touch-up, usually do so with a little glue, but it can be quite `fiddly`....you`d need to keep the lace away from the glue until it`s almost `cured`..... some tapes may not even `take`to the glue...depends on a few things.... I reckon a glued front hairline is easier to touch-up with glue...... you are getting a poly strip....that`s very easy to work with.... I always found tape was really easy to apply to poly..it didn`t `lift`when I was peeling off the backing -papers....it frequently lifted from lace though and I`m not the most patient when it happens ! Even guys who use tapes at the front and contours, will often set them `back` a few millimeters from the very edge, and use glue to tack down that last little bit...you`ll find what works best for you after a while --it`s a case of experimenting really as it varies from one person to another as to what materials to use for bonds. Regards for now.
Reply


Messages In This Thread
New here - Trey22 - 01-16-2012, 07:44 AM
RE: New here - Hersute - 01-16-2012, 07:59 AM
RE: New here - Paul In Ireland - 01-16-2012, 09:31 AM
RE: New here - Trey22 - 01-16-2012, 08:46 PM
RE: New here - Aussie-Craig - 01-16-2012, 09:26 PM
RE: New here - Paul In Ireland - 01-16-2012, 10:16 PM
RE: New here - Trey22 - 01-18-2012, 04:37 AM
RE: New here - furball - 01-19-2012, 03:55 AM
RE: New here - Trey22 - 01-19-2012, 05:15 AM
RE: New here - furball - 01-19-2012, 10:15 PM
RE: New here - Paul In Ireland - 01-19-2012, 05:41 AM
RE: New here - Hersute - 01-19-2012, 06:16 AM
RE: New here - Hersute - 01-19-2012, 11:27 PM
RE: New here - Paul In Ireland - 01-20-2012, 12:04 AM
RE: New here - furball - 01-21-2012, 01:42 AM
RE: New here - Hersute - 01-21-2012, 01:48 AM
RE: New here - Trey22 - 01-26-2012, 08:46 PM
RE: New here - Trey22 - 01-29-2012, 10:28 PM
RE: New here - Hersute - 01-30-2012, 12:15 AM
RE: New here - Trey22 - 02-24-2012, 04:51 AM
RE: New here - Edward - 02-24-2012, 05:44 AM
RE: New here - Trey22 - 02-24-2012, 07:53 AM
RE: New here - Edward - 02-24-2012, 08:08 AM
RE: New here - Trey22 - 03-18-2012, 05:03 AM
RE: New here - EricInNY - 03-18-2012, 05:16 AM
RE: New here - Trey22 - 03-22-2012, 01:15 AM
RE: New here - Hersute - 03-22-2012, 04:14 AM
RE: New here - Paul In Ireland - 03-22-2012, 05:04 AM
RE: New here - Trey22 - 03-22-2012, 07:02 AM
RE: New here - Paul In Ireland - 03-22-2012, 08:00 AM
RE: New here - Trey22 - 03-24-2012, 04:16 AM
RE: New here - Paul In Ireland - 03-24-2012, 06:55 AM

Forum Jump:


Users browsing this thread: 6 Guest(s)